Insulation
Rigid insulation and a cover board form the base for a smooth surface.
Flat Roofing
Rubber Roof Installation Secaucus, NJ
A roofer in Secaucus can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, so the roof handles sun, cold and storms for decades. Dial (551) 373-3020 to talk with a local roofer about a new rubber roof.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. The membrane is thick, stretchy rubber that tolerates temperature swings and resists hail and sunlight well. That flexibility is why it suits so many homes.
EPDM can be attached in three main ways. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. On most homes, fully adhered EPDM is the usual choice because it handles wind well and stays smooth.
Then comes thickness and color. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. Black is standard and holds heat, while white reflects it. Where the rubber meets a shingled roof or the house wall, the tie-in detail matters as much as any of these choices.
Rubber Roof Installation is often paired with rubber roof repair and flat roof installation, depending on the cause.
Need rubber roof installation in Secaucus? Call (551) 373-3020 to talk to a local roofer.
Call nowThe process
What happens during a rubber roof installation
A rubber roof is built in layers, with the seams and flashing as the critical details.
Check the base
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. Old roofing is removed if the roof is being replaced.
Add the cover board
Rigid insulation, often polyiso, is fastened with plates and screws, then a cover board goes on top. Slope can be built in at this stage.
Lay the sheet
The membrane is unrolled, aligned and allowed to settle before bonding. Seam layout follows the direction of drainage.
Bond the membrane
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Each half gets the same treatment in turn. Air pockets left under the sheet can turn into blisters later, so the crew works the rubber flat from the center out.
Seal the seams
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Exposed edges get lap sealant.
Flash the details
Walls and curbs get membrane flashing held by termination bar, pipes get pre-molded boots and corners get uncured flashing. Termination bar and counter flashing seal the wall edge. The last step is probing each seam and patch for gaps.
What is included
What goes into a rubber roof
Tear-off
The base is cleared and checked for a sound start.
Flashing
Walls, curbs, pipes and edges are flashed for a finished roof.
EPDM membrane
Wide sheets of EPDM cover the roof with as few seams as possible.
Seams
Every seam gets primer and tape for a lasting bond.
Related service
EPDM Roof Installation Secaucus, NJ
The quality of an EPDM installation shows up years later in the seams and edges. A flat, dry base, properly timed adhesive and carefully primed seams are what make EPDM last. Dry, mild days give the best bond. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
In Secaucus, an experienced EPDM installer leaves room for the membrane to move and age. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask about edge securement before work starts.
Local help
Rubber Roof Installation Near Me
Rubber roofs in Secaucus are common on porches, garages, additions and flat sections of older homes. From Secaucus to neighboring communities such as Union City, East Rutherford, West New York and North Arlington, rubber roofs that drain properly and have well sealed flashing last the longest, so installation details matter as much as the material.
For rubber roof installation in Secaucus, NJ or nearby towns like Union City, East Rutherford, West New York and North Arlington, call (551) 373-3020 to reach a roofer who covers your street.
What the local climate does to a roof
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Secaucus, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why not wait
Less damage
Small roof problems caught early usually stay small repairs.
Familiar with local homes
Local roofers see the same roofs and storm damage across Secaucus and nearby towns.
Know what happens next
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Installation questions
Can a rubber roof go over an existing roof?
Recovering depends on the condition of the old roof. The old roof must be a single dry layer, with a recover board over it. Wet insulation or multiple layers mean a tear-off. The roofer tests the old roof for moisture before recommending a recover.
How thick should a rubber roof be?
EPDM usually comes in 45 or 60 mil for homes. The thicker sheet holds up better to traffic and weather. Heavy duty options exist too.
Should my rubber roof be black or white?
Black and white each have their place. Black holds heat and white reflects it. A roofer can recommend what fits your home.
What is the difference between EPDM and TPO?
The two are different materials. Black EPDM is taped and stretchy, and white TPO is welded and reflective. A roofer can help you choose.
How long does a new rubber roof last?
Rubber roofs often last decades. Good seams, drainage and occasional checks make the difference. Repairs are simple when needed.
More questions? Call (551) 373-3020
Other services that may help
Rubber Roof Repair
Repairs for leaking rubber roofs, from peeling seams to pulled flashing at walls and curbs, never with tar or asphalt cement that ruins the rubber.
Learn moreFlat Roof Installation
New flat roofs built with real slope, insulation, a cover board and a membrane suited to the building, planned around how the roof will be used.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, built around proper drainage, flashing and edge metal.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesTalk to a Secaucus roofer about rubber roof installation
Call (551) 373-3020 to talk to a roofer serving Secaucus, NJ.